Woodmont Doors
Series 800 RTF raised panel and slab rigid thermal foil cabinet doors


Woodmont Series 800 RTF rigid thermal foil doors and corresponding drawer fronts will both be shown on this web page. Profile selection diagrams will also be shown.
AFTER the Woodmont Doors photos that we took will be old Quality Doors cross reference information to assist former Quality Doors customers. We can help with many of the Quality Doors designs that were discontinued in December of 2009.

FAIR WARNING: We are going to give you a ton of data about Thermal Foil doors on this page. We are also ending the page with a good amount of info about the older Quality Doors RTF doors to aid you should you be matching to existing doors. This is not a web page to just whip through. If you choose to print it, set your printer setting to "PRINT TO FIT" and your printer will squeeze the width and you won't lose any of the info. We welcome e-mail questions about the doors, and we do respond to e-mails.
 


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
Normal square top design: style 800.


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their RTF thermal foil doors
LEFT: Design 800 raised panel RTF door, C2-113 profiles, shown in Matte White RTF finish.
ABOVE: close up of the C2 inside pass profile and the 113 perimeter edge.
As you can see from the upper left side of the photo, matte white will have a minor amount of shine to it. Matte White is a bright white finish with a satin sheen.
Minimum sizes for design 800 door:
C2-113 profile width 7-3/8" x height 7-3/8".
C3-113 profile width 7-1/2" x height 7-1/2"
C4-191 profile width 7-7/8" x height 7-7/8".
Maximum size is 31" wide by 90" tall.

For matching raised panel drawer fronts, request them as either:
design 800F - same min. requirements as design 800 door;
or as design 800FC reduced rail. Min. height requirements:
C2 = 5-3/8"; C3 = 5-1/2"; C4 = 6-3/8".
For a slab drawer face, order as 8DF-113. Min. width 3" x height 3".

Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
Design 801 cathedral top door. Shown with C4-191 profiles, antique white.


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
LEFT: Design 801 raised panel RTF door, C4-191 profiles, antique white RTF.
Minimum size for design 801 door:
C2-113 profile width 10-3/8" x height 10-3/8".
C3-113 profile width 10-1/2" x height 10-1/2"
C4-191 profile width 10-7/8" x height 10-7/8".
Maximum size is 31" wide by 90" tall.

For matching raised panel drawer fronts, request them as either:
design 800F - same min. requirements as design 800 door;
or as design 800FC reduced rail. Min. height requirements:
C2 = 5-3/8"; C3 = 5-1/2"; C4 = 6-3/8".
Note: drawer fronts are square top, no arches.
For a slab drawer face, order as 8DF-113. Min. width 3" x height 3".
 


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
Roman arch style door: design 805.


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their kitchen cabinet doors
LEFT: Design 805 raised panel RTF door, C3-113 profiles, shown in Almond RTF finish.
ABOVE: close up of the C3 inside pass profile and the 113 perimeter edge.
As you can see from the upper left side of the photo, almond RTF will have a minor amount of shine to it. Almond is a deep ivory color with a satin sheen.
Minimum size for design 805 door:
C2-113 profile width 10-3/8" x height 10-3/8".
C3-113 profile width 10-1/2" x height 10-1/2"
C4-191 profile width 10-7/8" x height 10-7/8".
Maximum size is 31" wide by 90" tall.

For matching raised panel drawer fronts, request them as either:
design 800F - same min. requirements as design 800 door;
or as design 800FC reduced rail. Min. height requirements:
C2 = 5-3/8"; C3 = 5-1/2"; C4 = 6-3/8".
Note: drawer fronts are square top, no arches.
For a slab drawer face, order as 8DF-113. Min. width 3" x height 3".
 


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
Beaded Shaker style door: 800 S5-118.


DL beaded shaker door - Quality Doors DL Beaded Shaker style door
LEFT: Design 800 beaded panel Shaker RTF door, S5-118 profiles, shown in Woodgrain White RTF finish.
ABOVE: close up of the S5 inside pass profile and the 118 perimeter edge. S5-118 profile combination is the popular "beaded shaker style door."
Woodgrain White is a bright white finish with a satin sheen. Woodgrain White and Matte White are the same color, but Woodgrain white has a woodgrain appearance.
Minimum size for design 800 S5-118 door: width 8" x height 8".
Maximum size is 31" wide by 60" tall.

For matching beaded shaker style drawer fronts, request them as:
design 800F S5-118 = all four rails same as door, min. size 8" x 8";
or as design 800FC S5-118. Min. height requirement 4-1/2".
For a slab drawer face, order as 8DF-118. Min. width 3" x height 3".
 


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
Shaker style door: 800 S4-118.


Woodmont Doors Quality Doors DL Shaker door
LEFT: Design 800 shaker style RTF door, S4-118 profiles, shown in Autumn Oak RTF finish.
ABOVE: close up of the S4 inside pass profile and the 118 perimeter edge.
Autumn Oak RTF is the common honey looking or golden oak tone color. Note, Woodmont Doors version of Autumn Oak does not contain that reddish hue that Quality Doors version of Lite Oak had. Not an exact match.
Minimum size for design 800 door: width 8" x height 8".
Maximum size is 31" wide by 60" tall.

For matching shaker style drawer fronts, request them as:
design 800F S4-118 = all four rails same as door, min. size 8" x 8";
or as design 800FC S4-118. Min. height requirement 4-1/2".
For a slab drawer face, order as 8DF-118. Min. width 3" x height 3".
 


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil drawer fronts
ABOVE: Design 800FC raised panel RTF drawer front, C4-118 profiles, shown in Almond RTF finish.
RIGHT: close up of the C4 inside pass profile and the 118 perimeter edge.
Minimum sizes for design 800FC drawer front:
widths: C2 = 7-3/8"; C3 = 7-1/2"; C4 = 7-7/8".
heights: C2 = 5-3/8"; C3 = 5-1/2"; C4 = 6-3/8".

For matching raised panel doors, request them as design 800 C4-118.
 


Best match for the 700 HV3-191 cabinet door
Notice how the top and bottom rails are narrower. This is how the 800FC drawer fronts are made. Left and right frame rails are identical width to the doors. But top and bottom rails are narrower. Close up of the C4 inside profile above.
If you want all 4 rails to be the same, note the minimum height requirements and order as 800F (same as 800 doors).


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their RTF doors


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
LEFT: Design 800 slab face RTF door, S2-191 profiles, shown in Pear RTF finish. (Very similar to Cherry grain.)
ABOVE: close up of the 191 perimeter edge.

Minimum size for design 800 door with "S2" profile: width 3" x height 3".
Maximum size is 31" wide by 90" tall.

For matching slab drawer face, order as 8DF-191. Min. width 3" x height 3".

Note: grain on doors runs vertical. Grain on drawer fronts will run horizontally. This is true of all RTF designs.


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
LEFT: Design 800 slab face RTF door, S2-112 profiles, shown in Natural Maple RTF finish. (Very blonde maple.)
ABOVE: close up of the 112 perimeter edge.

Minimum size for design 800 door with "S2" profile: width 3" x height 3".
Maximum size is 31" wide by 90" tall.

For matching slab drawer face, order as 8DF-112. Min. width 3" x height 3".

Note: grain on doors runs vertical. Grain on drawer fronts will run horizontally. This is true of all RTF designs.
 


C2-113 thermal foil door - 700 C2-113 door


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors
LEFT: Design 800 raised panel RTF door, C2-113 profiles, shown in Pickled Maple RTF finish.
ABOVE: close up of the C2 inside pass profile and the 113 perimeter edge.
Pickled Maple is a white wash maple look.
Minimum sizes for design 800 door:
C2-113 profile width 7-3/8" x height 7-3/8".
C3-113 profile width 7-1/2" x height 7-1/2"
C4-191 profile width 7-7/8" x height 7-7/8".
Maximum size is 31" wide by 90" tall.

For matching raised panel drawer fronts, request them as either:
design 800F - same min. requirements as design 800 door;
or as design 800FC reduced rail. Min. height requirements:
C2 = 5-3/8"; C3 = 5-1/2"; C4 = 6-3/8".
For a slab drawer face, order as 8DF-113. Min. width 3" x height 3".


Eclectic-ware offer Woodmont Doors - custom made kitchen cabinet doors - help for Quality Doors customers looking to match their thermal foil doors






When considering your drawer front choice to go with your doors, basically you have 2 choices. A corresponding raised panel front or matching shaker style front to go with the shaker style doors - as long as your height requirement permits.

Or, just a slab drawer front. Slab means flat face. There is no raised panel or sunken panel profile. The drawer front is just flat, and then you would request it with a matching edge to go with your doors.

Shown to the left is a raised panel front above a Roman arch top door. We do not have a lot of samples to show a proper combination. This picture more or less was grouped because of the color of the drawer front and the door. Normally, base cabinet doors are square top and you have your drawer fronts above those. Arch top doors are a common mix for your upper cabinets. But the choices are yours to do as you like. A kitchen full of slab doors is a very nice look. Installing raised panel doors, but then slab drawer fronts is one of the most popular combinations out there.

You have many design choices that you can do. And it is your choice. There are no set rules about how it should be done. Just don't mix things up that really do not go together. As always, if you have any questions, you can e-mail us.

NOTES:
Drawer front design 800F has 4 equal size rails. It is the same as design 800 door. BUT, doors have vertically running grain for woodgrain patterns. An 800F drawer front will have a horizontally running grain.

Design 800FC will have reduced top and bottom rails to allow for shorter height requirements. All minimum heights are listed above.

Design 8DF slab drawer front can go with anything and allows for some really small sizes.

 

Inside pass profiles and edge profiles for RTF door selections.
Pass profile side cut views for Woodmont Doors RTF kitchen and bathroom cabinet doors

Slab drawer front edge choice for thermal foil cabinet drawer fronts

NOW FOR THE IMPORTANT STUFF to know about the RTF doors.

Basically, there are only three door styles shown above: 800, 801, and 805.
Designs 800, 801, and 805 can be made with ANY of the pass profile and edge profile choices that you would like.
Thus C2, C3, and C4 can be requested in square top doors(800), cathedral top(801), and Roman arch top(805).
The 112, 113, 118, and 191 edge choices can be made with any of the pass profiles. If you want a C4-191 or a C4-113, or whatever, you can have it. Mix them up.
Design 800 S2 slab door can be made with edges 112, 113, 118, or 191. Request it how you like it.
Design 800 S4-118 door comes only with the 118 edge. This is the specialty shaker style door.
Design 800 S5-118 comes only this way. This is the specialty beaded shaker style door.
800F drawer fronts will have 4 equal size frame rails, matching to the doors. 800FC will have narrower top and bottom rails. 8DF are slab drawer fronts.
Every door design is available in all 8 RTF colors shown below.
Any question? Please
e-mail us.
 

RTF Color selection:
Matte white and white woodgrain are bright whites, but not glossy. On the white woodgrain, you will see a grain pattern.
The antique white is more like a bone color; it is an off white. Almond is darker than antique white.
The woodgrain colors are displayed well below.
The images shown below are actual scans of the RTF material. They are good representations.
(The dark streak in the bottom right corner of each color is dirt on the bottom of our scanner glass that we cannot clean - ignore it.)
nof="te"

matte white thermal foil doors
Matte White

white woodgrain RTF cabinet doors
White Woodgrain

antique white thermal foil kitchen cabinet doors
Antique White

almond RTF cabinet drawer faces
Almond

natural maple RTF doors
Natural Maple

pickled maple RTF cabinet door fronts
Pickled Maple

Autumn oak RTF kitchen doors - Lite Oak RTF
Autumn Oak

Pear RTF thermal foil doors
Pear



 

Old Quality Doors help is still farther down the page.

If you would like your doors bored for concealed 35mm cup hinges,
please select boring option #1 or option #2 as shown below.
**For designs 801 or 805, state BL (bore left); BR (bore right); BP (bore as pairs).
Hinges for 1/2" overlay on a face frame edge mount are available from Woodmont Doors.
Concealed hinge boring diagram for kitchen cabinet wood doors
To view actual pictures of the hinges, and other concealed hinge options, please select this link.

Pricing:

We will calculate it for you. Please request a quotation.

 

How to order series 800 RTF (rigid thermal foil) doors:

  • Select your door design: designs 800, 801, 805
  • Select an RTF color choice: Matte White, Antique White, Almond, Woodgrain White, Natural Maple, Pickled Maple, Autumn Oak, or Pear
  • Select a pass profile from the graphic shown higher on this page: C2, C3, C4, S2, S4, S5
  • Select an edge profile form the graphic shown higher on this page: 112, 113, 118, 191 (note restrictions above for shaker theme doors)
  • Enter all your door quantities and sizes in inches (examples: 15-1/4, 32-1/16, 6-1/2, no need for " marks)
  • If you need drawer fronts, state the design: 800F, 800FC, or 8DF slab and then your pass profile and edge choice (most likely same as the doors)
  • Enter all your drawer front quantities and sizes
  • If you need the doors bored for concealed hinges, state boring option #1 or #2
  • If you need hinges for a 1/2" overlay on a face frame mount, get them now

On-line ordering page or quotation requests

 

Customer testimonials:
Thank you John! This is the fifth time I have used your firm. I have been very pleased with your products.
Steve H., Middle Island, NY - ordered Woodmont 800 S5-118 beaded shaker style RTF doors.

Doors were received in good condition and are now installed. Thank you,
Michael A., TwelveStone Construction - ordered RTF cabinet doors.


Information about ordering frame only or mullion RTF doors:

Frame only doors are a door with a big hole in the middle for your glass panel. It is just the top, bottom, and left and right frame rails with one large opening. Mullion doors are the same frame but with mullion rails to create multiple openings within the entire large opening. Any of the above raised panel or shaker panel RTF doors can be ordered as frame only (FO) or as mullion doors. Mullion doors can be 4-lite, 6-lite, 8-lite, and on square top doors only, you could have 9-lite too (3 rows and 3 columns). Styles 801 and 805 will have only 2 columns, but can have 2, 3, or 4 rows of lites.

Maximum size on any frame only or mullion RTF door is 31" x 60".
Minimum size requirements vary a little by what is shown for solid panel doors above. Most are about an inch larger in height and width.

RTF thermal foil mullion cabinet doors

thermal foil mullion kitchen cabinet doors

RTF Refacing accessories:

RTF refacing sheets:
Thermal foil (PSA) pressure sensative adhesive backed sheets in 24" x 96" are available.
24x96 sheet in any RTF color shown above.

 

RTF plywood - cut to size
minimum size 3-1/2" width, 3-1/2" height.
maximum size 48" width, 96" height.
Grain (woodgrain patterns) runs with the height dimension.
(Note: grain is understood to be vertical. If using horizontally, grain still runs with the measurement defined as height.
Thus, when used for toekick, you can order as 3-1/2" x 96", or 4" x 96" [or any length]. Grain runs with the long measurement.)

 

RTF moulding selections:
Woodmont Doors RTF moulding selections


 

 

Quality Doors old RTF door information:
We had offered Quality Doors from 2001 through their shutdown in December of 2009. With their shutdown, it did present some obstacles in offering high quality custom sized doors. Fortunately, Woodmont Doors has expanded their Thermal Foil door selections to match several of the Quality Doors styles and to offer some close substitutes on a few more designs. The two graphics below we have created to help you to know Woodmont Doors RTF doors a little better and how the designs compare to Quality Doors. After the two graphics, we will explain some of our notes on the graphics and some data about the RTF color cross references.

Eclectic-ware information on how Quality Doors customers can find substitute door choices with Woodmont Doors

Please note: the Woodmont Doors pass profile diagrams are shown higher above on this page.
Eclectic-ware information on how Quality Doors customers can find substitute door choices with Woodmont Doors
The two graphics above were created by Eclectic-ware and are for exclusive use on our web site only.

Notes about Woodmont Doors to Quality Doors comparisons:
Door designs are the same:
WD's 800 is QD's 700, the 801 is the 701, the 805 was QD's 716.
Profiles: WD's C2 is the same look as QD's C2, but it is not quite as wide.
WD's C3 is exclusive to Woodmont, it does not match any QD pass profiles.
WD's C4 is a good substitute for WD's HV3, but it is not identical. There are a few contour differences.
WD's S2 slab is the same as QD's 77R2, 112 edge is identical too.
WD's S4 shaker style, and the S5 beaded shaker style are 99% matches. The reason we
say 99% is because the WD frame rails measure 2" and the QD frame rails measure 2-1/16". If you measure
them side by side you can tell this. If you do not measure them, you cannot tell the difference.
WD's 112 edge matches QD's 112, the 113 matches the 113, the 118 matches QD's 115.
The 191 edge is a very close match to QD's 191, but not an exact match.
Colors: WD's matte white is a spec more brighter and crystal-like than QD's matte white, but an excellent substitute.
WD's woodgrain white seems to be a 100% match to QD's woodgrain matte white.
WD's antique white is a 98 to 99% match to QD's antique white.
WD's almond is an exact match to QD's almond.
WD's pear is an exact match to QD's pear.
WD's Autumn Oak is a little lighter and more on the brown tone than QD's Lite Oak. No reddish hue.
WD's Natural Maple is a little lighter and much better looking that QD's natural maple.
WD's pickled maple is a cross between QD's Sanibel Maple and Dunwood. The pickled maple looks
more like a natural whitewash color but without that pinkish hue to it.
Woodmont does not have a match to the Dunwood or Sanibel Maple. Their pickled maple is meant as
a sub for either, but it does not match either.

If you are looking to add a door or two to your kitchen that has Quality Doors in it, some Woodmont
designs can fill that need, some are close, and you could be out of luck if none of the above info helped.

The reason we have the above data is because we compared our old Quality Doors sample doors to the
sample doors we received from Woodmont. So all of the above references are from us and no other
source. And we did double check our comparisons. This is the most accurate data you will find.


Door choices, measuring and installation information, hinge info, and quotation and ordering links are in the top margin of this page. Scroll back up.

Solve your odd size hole center to center problem.
Answers here.

Got 2-3/4", 3-1/2", or any crazy size
?

We ship orders worldwide.  We have had many customers from Canada, England, Australia and other predominately English speaking nations that we advertise in.  We have shipped all througout Europe, and to several Asian, African, and South American countries.
We ship everywhere:

friends
Tell a friend about our web site!

Navigate back to any section of our web site using these links:

Or navigate by our product category pages:

Close-out products:

HOME > WOODMONT DOORS > Please SELECT from these door and accessory pages while in the WOODMONT DOORS section of our website: (Best viewed on a PC or tablet)

DOORS: Mitered corner raised panel wood doors | M&T corner raised panel wood doors | Shaker style plywood panel wood doors | Wood drawer fronts | Frame only and Mullion wood doors
RTF thermal foil doors | Melamine doors
ACCESSORIES: Wood drawer boxes | Veneer, decorative molding, and cut to size plywood

HELP PAGES: Face frame & frameless cabinets explained | Profile choices for wood doors - frames, panels, edges | How to measure your doors and installation tips | Questions about custom made cabinet doors | Customer testimonials

QUOTES / ORDERING: On-line quotation and ordering form | FAX quotation and ordering form

cc-symbols5

When you are ready to place your order, please open our on-line ordering form here
Or you can place a phone order from 9 to 5 Mon-Fri EST, call us at 813-633-7544 or 813-362-7898.
You can FAX or mail in orders too.

SUPPORT AMERICAN OWNED & OPERATED SMALL BUSINESSES

 

Eclectic-ware is a distributor of cabinet and bathroom hardware
Eclectic-ware

3110 Turkey Walk Lane
Wimauma, FL  33598  USA
(Greater Tampa to Sarasota area)
Phone: 813-633-7544
FAX: 813-634-3400
website: www.eclectic-ware.com

EclecticWare is a BBB Accredited Home Kitchen Cabinetry Equipment Supplier in Wimauma, FL
A+ rated business since 2003

Customer service hours
& phone (813) 633-7544
and (813) 362-7898 cell
Mon-Fri 9 to 5 E.S.T.
24/7 FAX and on-line ordering.
Anyone can purchase from us!
 

© Copyright 2000-present ~ John W. Wagonis | Established Dec. 2000 | County license # 146460
Home | Sitemap | Our Blog | Contact Us | About Us | How to order page
Testimonials |
F.A.Q. | Return policy | Privacy policy

Are you a little lost?

 

Eclectic-ware kitchen cabinet hardware and bathroom accessoriesWoodmont Doors Kitchen Cabinet Doors

813-633-7544 main line -- or 813-362-7898 cell
for phone orders, product questions, & design assistance.

 

 

 

 

Click here to order. Visa, MasterCard, American Express, Discover card accepted by Eclectic-ware
Click for the BBB Business Review of this Kitchen Cabinets & Equipment - Household  - Shipping throughout the entire USA, Canada, and worldwide

We are a cabinetry and bathroom hardware supply store open to everyone!
Please remember the hyphen (-) in Eclectic-ware and in our web address: www.eclectic-ware.com

HOME | PRODUCTS | MANUFACTURER INDEX | CONTACT US | SITEMAP | RESOURCES | BLOG